How to use the fish tank heating rod (how to use the fish tank heating rod)

×

How to use the fish tank heating rod

This article tells you how to use the Fish tank heating rod and the relevant information about how to use the fish tank heating rod. I hope it will be helpful to you and don't forget to pay attention to our Xianglong Fish Farm.

The contents of this article:

• 1 、Application method and related introduction of heating rod

• 2 、Correct use of electric heating rod in fish tank

• 3 、How to adjust the temperature of the fish tank heating rod

• 4 、How to put the heating rod in the fish tank

• 5 、Correct use of heating rods in fish tanks

Application method and related introduction of heating rod

In the new period of the increasing development of living standards, the application of new materials has become an irresistible inevitable trend, whether at home or away from home is necessary for aquarium farming. Heating tools such as electric heating rods play a more important role in daily life, and they are equally important in production. As a commonly used equipment, they are also different in quality, price, and production process. The following editor will take you to understand the specific content of the use of heating rods.

Heating rod use temperature setting

There are too many brands of heating rods, and now the quality of domestic products is relatively good, such as innovation, silver sound, etc., imported such as thunderwolves, integrated shelves. Heating rods have a service life, usually no more than two winters. Over time, the wire is aging and the contact is oxidized, which may fail. Even for imported heating rods, the life claimed in the manual is within 1-2 years. To be on the safe side, you can combine the heating rod with the thermostat. There are many brands of domestic thermostats, and the price is not high. Set the temperature of the heating rod to be 2 ℃ higher than the thermostat, so that double insurance can avoid the tragedy of cooking fish soup.

Power of heating rod

Heating rod power selection problem: generally calculated according to the volume of the cylinder, each liter of water should have 2w heating power, if the water in a cylinder has 300 liters, then the total power of the heating rod is at least 600w. Heating in winter is probably one of the most power-consuming expenses. I strongly suggest that you should take good measures to keep warm in your vats. Buy a few 2 cm thick foam boards, paste the back and side of the tank, and make a good airtight lid for the fish tank, which can greatly reduce energy loss. It only takes a little time and a small amount of money, but it can save a lot of electricity bills. Why not? You know, every penny handed over is our own reward for our work, so why do we have a problem with our wallets?

Placement of hot rods

Hot rod placement: to raise large fish, the heating rod should be fixed safely, because some big fish can easily hit the cylinder wall and break it by throwing off their tails. The heating rod should not be buried in the bottom sand and should not come into direct contact with the glass. Once upon a time, some fish broke because the heating rod directly contacted the glass, which caused the glass to be heated unevenly. Put the heating rod diagonally or horizontally, the heat dissipation effect is better, although this may not look good. Because the heated water is rising, the temperature difference between the hot water produced in the lower part of the rod and the upper part of the rod is relatively small, and the heat conduction will be slower, which undoubtedly reduces the heating efficiency, prolongs the heating time and wastes energy. For relatively clumsy fish like Hong Hong, it is best to add a casing to the heating rod to prevent the fish from being scalded. If there are two heating rods in the cylinder, try to divide them on both sides of the cylinder and heat them evenly. The thermometer should be placed farthest from the heating rod to ensure that the water temperature is not from the hot water that has just been heated.

The state of the heating rod

You'd better have a spare heating rod at home. Otherwise, if the stick breaks at night, you don't have to jump in a hurry.

The red light of the heating rod does not indicate that the working condition is good, and the water temperature should prevail. Because if the resistance wire is broken and the water temperature drops, the bimetal turns on the circuit, but it cannot be heated, so the red light will be on for a long time. Of course, sometimes the temperature reaches, the metal sheet can not be broken, it is possible to cause the temperature to rise continuously, which will also show that the red light is on.

The difference in saving electricity between imported heating rods is also very small (saving 1 kilowatt-hour a month is not a big deal). In terms of reliability, an imported heating rod with more than 100 yuan can buy 7 or 8 domestic brands with 15 yuan (such as Yinsheng). Even if the imported goods can be used for 5 or 6 years (do you rest assured?), it is not as reliable as the domestic one year. From the safety point of view, 15 yuan plus a 40 yuan out-of-cylinder thermostat, the safety is comparable to the single temperature control of a heating rod no matter how much it costs! In fact, the main difference between expensive and cheap heating rods is the accuracy of constant temperature control, but this can also be made up for by an out-of-cylinder thermostat. Therefore, the rational analysis should be the use of 15 yuan heating rod, plus a thermostat.

Usage of heating rods

Put the heating rod diagonally or horizontally near the bottom of the tank in the aquarium, so that the heat dissipation effect is better, because the water will rise after heating, and the temperature difference between the hot water produced in the lower part of the rod and the upper part of the rod is relatively small. Heat conduction will be slower, which undoubtedly reduces the heating efficiency, prolongs the heating time and wastes energy. And the temperature control device is on the top of the heating rod, which will cause the heating rod to stop heating ahead of time. But it doesn't look very good in this way, so many people still prefer to use heating rods vertically. At this time, it is necessary to cooperate with a thermometer to adjust the water temperature. The thermometer should be placed away from the heating rod to ensure that the water temperature is not from the hot water that has just been heated.

Usually, if the shell of the heating rod is broken, do not panic, generally will not electrocute the fish, just take out the electricity and exchange it for another one. Normal use is generally unbreakable, which is caused by people taking it out of the water surface when changing water or cleaning, without power outage, or accidentally touching a hard place. Take it out after the power is cut off for a while, otherwise the remaining temperature will be enough for you.

Choose the right heater

When choosing a heater, the problem of power matching must be considered. generally speaking, 10 watts of power is needed for every 5 liters of water. For example, an aquarium with a length of 90 cm, a width of 30 cm and a depth of 38 cm with a volume of 100 liters should choose a 200 watt heater. For larger, 90 or more aquarium tanks, two 100-watt heaters are needed and placed at both ends of the aquarium, so that the heating is uniform and the effect is better.

Now, small aquariums are also equipped with high-power heaters, but if the performance of the heater is not good, it will be very dangerous, especially when the heater is in abnormal "work", the water will quickly heat up, or even boil and burn your fish to death. The high temperature makes the glass tank possible to burst.

Moreover, the smaller the aquarium, the faster the temperature changes. If the heater is too large, it will start and stop frequently, which can easily damage the constant temperature control element and lead to the heater failure. On the contrary, large aquariums with low-power heaters can only reach their maximum load and are useless when the ambient temperature is too low.

The above is the relevant content shared by the editor about the use of heating rods. The prices of different heating rods are different, and the quality processes are also different. We can choose between different manufacturers according to their specific needs, in order to achieve the best use effect. Of course, with the continuous improvement of our living standards, different new heating rods will gradually appear. The above is our sharing. I hope it will be helpful to all of you.

Correct use of electric heating rod in fish tank

The correct use of the electric heating rod in the fish tank: the heating rod is completely placed in the water and placed in the middle of the tank.

Fish tank heating rods should not be electrified in the air. Because it heats up extremely fast in the air, it burns out the heating rod, or shatters the glass or burns the hand. Even if the power is cut off, it can not be taken out of the water immediately, the temperature at this time is also very high, and it is also easy to burn people and burn out the heating rod.

Extended data:

Points for attention in the placement of heating rods:

To raise large fish, the heating rod should be fixed safely, because some big fish can easily hit the cylinder wall and break them by throwing off their tails. The heating rod should not be buried in the bottom sand and should not come into direct contact with the glass. Once upon a time, some fish friends broke because the heating rod directly contacted the glass, which caused the glass to be heated unevenly.

Put the heating rod diagonally or horizontally, the heat dissipation effect is better, although this may not look good. Because the heated water is rising, the temperature difference between the hot water produced in the lower part of the rod and the upper part of the rod is relatively small, and the heat conduction will be slower, which undoubtedly reduces the heating efficiency, prolongs the heating time and wastes energy.

For relatively clumsy fish like Hong Hong, it is best to add a casing to the heating rod to prevent the fish from being scalded. If there are two heating rods in the cylinder, try to divide them on both sides of the cylinder and heat them evenly. The thermometer should be placed farthest from the heating rod to ensure that the water temperature is not from the hot water that has just been heated.

Source: Baidu Encyclopedia-heating Rod

How to adjust the temperature of the fish tank heating rod

The fish tank heating rod is an indispensable tool in the aquarium, and it is also a necessary tool to provide warmth and comfort for the aquarium. Some novice fish friends will not know how to correctly use the heating rod to adjust the temperature of the aquarium. The editor will introduce it to you in detail.

ornamental fish

The heating rod is mainly to improve the water temperature, such as the temperature regulating device of the constant temperature heating rod in the aquarium, and a metal switch piece is arranged between the contact piece and the bimetal sheet, and the temperature of the heating rod is adjusted by the switch piece.

According to a manufacturer, the two sides of the bimetal sheet are made of different materials. when connected with the external power supply, the coefficient of thermal expansion is different, and when heated, the deformation of the two sides of the bimetal sheet is different, resulting in the bimetal sheet tilting to one side. according to this principle, the bimetal sheet is adjusted to a certain extent by the adjusting switch, at this time, the bimetal sheet is absorbed by the magnetic body, and the bimetal sheet is pressed on the contact sheet. A metal switch sheet is sandwiched between the bimetal sheet and the contact piece, and the external current flows to the contact piece through the metal switch sheet to supply power to the heating wire.

Because the current does not pass through the bimetal sheet, the calorific value of the current will not affect the deformation of the bimetal sheet, which allows the temperature control device to pass through a larger current and adapt to a wider range.

Generally speaking, for aquarium friends, as long as you operate according to the purchase instructions, the heating rod can work normally. If you encounter quality problems, you can find the factory for replacement or maintenance after sale.

How to put the heating rod in the fish tank

The heating rod is an indispensable item in the fish tankHow to use the fish tank heating rodA good heating rod can keep the fish tank at a stable temperature. How to put the fish tank heating rod? BelowHow to use the fish tank heating rodI will introduce the relevant content to you.

1. The balanced arrangement is to place the heating rod flat at the bottom of the fish tank.How to use the fish tank heating rodThis method does not take up space and the heating effect is good.

2. The heating effect of vertical display is a little worse than that of balanced display, but the two kinds of display are very beautiful.

3. Neither of the two ways can be placed at a dead corner, nor can it be placed close to the edge of the fish tank. Leave a distance when placing, this can increase the activity space of the fish, it is not easy to get stuck, and the temperature of the heating rod should not be too high, otherwise the fish will not survive.

2. Types of heating rods

1. Heating rod without temperature control

Because the temperature can not be adjusted by direct heating, it can not be used alone.

2. Integrated temperature control heating rod

When the set temperature is reached, the power will be cut off by itself, and it is placed in the fish tank to control the temperature, so it is not very convenient when the temperature needs to be adjusted.

3. Water external temperature control heating rod

This kind of heating rod is more convenient to use, and the button to adjust the temperature is outside the fish tank, and the water temperature in the fish tank can be adjusted at any time.

4. Separate temperature control heating rods

Its temperature regulating probe is so light that if it leaves the water, it will not be able to control the water temperature in the fish tank.

Matters needing attention for heating rods

1. The heating rate of the heating rod is so fast that it should not be electrified when exposed to the air, otherwise it is easy to burn or break.

2. The service time of the heating rod is limited, because the metal sheet in the heating rod has been used for a long time.How to use the fish tank heating rodIt is easy to fail, so it is best to replace it every 1-2 years.

3. The heating rod should not be exposed when changing water for the fish tank.

4. Spare heating rods can be equipped at home to prevent sudden damage to the heating rods and affect the water temperature of the fish tank.

Conclusion: the quality of the heating rod directly affects the water temperature in the fish tank, and the water temperature affects the survival rate of the fish, so it is very important to choose a good heating rod. The above isHow to use the fish tank heating rodMy answer to the question about the type and use of heating rods.

Correct use of heating rods in fish tanks

Fish tank heating rodHow to use the fish tank heating rodThe correct usage is as follows:

First, choose a heating rod that is the right size for a fish tank.

Nowadays, the common heating rods in the world are glass tubes, stainless steel tubes, and ceramic tubes. If the requirement is not high, it is suggested to buy a glass tube with a relatively safe fish culture, the price is also relatively appropriate, the heating rod of stainless steel pipe has the phenomenon of Fish Filets in Hot Chili Oil, while the relatively high price of ceramic pipe belongs to high-end products.

2. Power selection of heating rods

The common ones are 100 watts, 200 watts, 300 watts, 100 watts for small cylinders, 200 watts for medium-sized cylinders, and 300 watts for larger cylinders, depending on the size of the water body and the temperature difference in the house.

Therefore, it is also appropriate to choose a heating rod, such as a small tank at home, but the room is very cold, at this timeHow to use the fish tank heating rodWe also need high-power ones to buy heating rods. If the temperature difference is small, it is already suitable for raising tropical fish, and we can buy heating rods with a little lower power.

Be sure to use the sucker of the heating rod to absorb to the wall of the fish tank to fix it, and it is a position that no fish can touch, preferably without stumbling, so as not to break the heating rod, so that it is easy to have the situation of Fish Filets in Hot Chili Oil.

The role of heating rods

Heating rods can cure fish, some fish have white spot disease, especially goldfish are more likely to get this disease.How to use the fish tank heating rodHis fish is bigger, at this time we can heat up the goldfish, add some salt to the fish tank and sterilize the fish, so that the disease can be cured over a period of time.

For example, when our cold-water fish suffer from white spot disease, we need to use heating rods to complete heating, while in changing water, heating up, and adding salt, the first point of warming is to speed up the metabolism of Ornamental fish. the second point is because we can increase the temperature to make ornamental fish more active to make ornamental fish disease better faster, and I think it can be the same as sweating after people catch a cold.

This is the end of the introduction of how to use fish tank heating rods. Thank you for taking the time to read the contents of this site. For more information about how to use fish tank heating rods and how to use fish tank heating rods, don't forget to find them on this site.

ASIAN AROWANA：

golden arowana priceGolden Arowana Such fish can start with much money？

Is the Rohan on the right worth 400?

How about a new pig nose on June 1st?

Aquarium installation

Withheld the fish what should I do？