How to install the governor of fish tank pump (fish tank pump installation)

×

How to install governor for fish tank pump

This article tells you how to install the governor of the Fish tank pump and the relevant information about the installation of the fish tank pump. I hope it will be helpful to you and don't forget to pay attention to our Xianglong Fish Farm.

The contents of this article:

• 1 、Fish tank frequency conversion pump how to speed ah?

• 2 、How to install the fish tank pump

• 3 、How to install and use the fish tank submersible pump?

• 4 、How to install pump Inverter

• 5 、How to install and use fish tank submersible pump

Fish tank frequency conversion pump how to speed ah?

Most frequency conversion pumps have knobs to adjust the flow rate. If not, a valve can be installed on the water pipe.

How to install the fish tank pump

Long pipeHow to install governor for fish tank pumpPlug one end into the submersible pump and the other into the drain box. YesHow to install governor for fish tank pumpWasHow to install governor for fish tank pumpyouHow to install governor for fish tank pumpIs the pump oxygenated? a thin tube is inserted into the pump at one end and the other end is fixed on the edge of the fish tank. Pay attention to the surface of the water.

When installing the submersible pump, the cable should be overhead and the power cord should not be too long. Do not force the cable when launching the unit, so as not to cause the power cord to break. Do not sink into the mud when the submersible pump is working, otherwise it will lead to poor heat dissipation of the motor and burn out the motor winding. During installation, the insulation resistance of the motor should not be less than 0.5m ∏: the motor below 13kW can be started directly, and the starting compensator should be used for those above 13kW.

Try to avoid turning on the computer at low pressure. The difference between the power supply voltage and the rated voltage should not be 10%. If the voltage is too high, the motor will overheat and burn out the winding, and if the voltage is too low, the speed of the motor will drop. If it does not reach 70% of the rated speed, the starting centrifugal switch will close, causing the starting winding to turn on for a long time and even burn out the windings and capacitors. Do not frequently switch the motor, this is because when the pump stops, it will produce reflux. If you start the motor immediately, it will start the motor load and cause the starting current to be too large and burn out the winding.

Do not let the electric pump overload for a long time, do not pump water with large sand content, and the time of dehydration and operation of the electric pump should not be too long, so as not to make the motor overheat and burn out. During the operation of the unit, the operator must observe at any time whether the working voltage and current are within the value specified on the nameplate. If not, the motor should stop running, find out the cause and eliminate the fault.

How to install and use the fish tank submersible pump?

1. Put the long sponge in first, be sure to put it properly, and don't leave any space.

2. Tighten the leaky parts at the bottom. If they are not tight, they will leak. It is better to check them again and again.

3. Place the card position parts close to the sponge on the card slot, where more details are required, and the parts are smaller and need to be careful.

4. Connect the pump to the long pipe and check the connection for leakage.

5. Install the filter.

6. The part of the rubber hose connected to the oxygen spray pipe.

7. Install the oxygen spray port up at the bayonet.

8. Connect the curved tube to the oxygen nozzle clamping position.

9. Connect the filter pipe with the curved pipe. Note that there is a row of holes facing down, and the holes must be downward.

10. Take the power plug out of the fish tank.

Note:

1. It can be used when the normal voltage is greater than or less than 15%.

2. If the power cord is damaged, please disconnect the power immediately.

3. Please clean the rotor and water blade regularly.

4. Before using it, the user must check whether the rated voltage of the pump is consistent with the actual voltage.

5. When installing or removing and cleaning the water pump, you must first unplug the power supply and cut off the power supply to ensure safety.

6. filter baskets and filter cotton should be cleaned frequently to ensure normal water intake and good filtration effect.

7. to protect the pump body, if there is any rupture, please stop using it immediately.

8. The maximum immersion depth of the pump into the water is 0.4 meters.

How to install pump Inverter

The mechanical installation of the water pump frequency converter is very simple, which can be installed directly by using the bolt hole on the frequency converter base.

The electrical installation of water pump frequency converter is the same as that of ordinary frequency converter. According to the pump parameters, set frequency converter parameters, wiring instructions will have a clear circuit diagram, reference can be!

How to install and use fish tank submersible pump

Introduction to the usage of fish tank submersible pump:

Fish 1 drowns the whole pump, otherwise the pump will burn out.

Fish 2 check whether there is a small branch above the pump outlet pipe, 90 degrees with the outlet pipe. This is the inlet, and as long as it is connected to the hose (random accessories), the other end of the plastic pipe will come out of the water and breathe in. There is a control knob (or other method) at the end of the tube that allows you to adjust the size of the intake. Check to see if it is installed or closed.

If the fish are farmed in bare tanks (only fish without water and grass) and the number of fish is large, then the external hose method can fill the water with more air, increase the amount of dissolved oxygen in the water, and help the fish to get more oxygen.

You can also add oxygen to water in the first way, which is through the rapid flow of water and the friction between water and air to increase dissolved oxygen.

The smaller the angle between the outlet and the water surface is, the greater the fluctuation of the water surface is, the greater the chance of friction between the water surface and the air is, and the more dissolved oxygen is. There is no need to change the direction of the first flow of water and then fall into the fish tank to get oxygen.

Extended data

Fish tank submersible pump

Performance and characteristics

● has good sealing performance, energy saving and stable operation.

● has high lift and large flow.

● is used in the water cycle of fish tanks and rockery.

● is suitable for all kinds of fresh water.

Specific parameters

Frequency: 50 Hz

Lift: 0.7 m

Maximum flow: 400 litres per hour

Reference link: fish tank submersible pump-Baidu encyclopedia

So much for the introduction of how to install the governor for the fish tank pump. Thank you for taking the time to read the contents of this site. For more information about the installation of the fish tank pump and how to install the governor, don't forget to find it on this site.

ASIAN AROWANA：

Cichlidae, can you help me to see how much this fish costs? Please approve the multi-pictures for me.

Great God helps out

Golden Catfish Could you help me identify what variety is there any hope of starting？ Now its 5cm

Maple Valley__Wild Three Lake Cichlids Please enjoy

GALLERY