How to do if the fish tank filter does not absorb water? (how does the fish tank filter not absorb water?)

×

What to do if the fish tank filter doesn't absorb water?

A list of the contents of this article:

• 1 、The filter of the fish tank does not absorb water, it rattles loudly, what is the reason, and the crossbeam is green.

  

• 2 、What if the filter in the fish tank can't absorb it?

• 3 、Waterfall filter why didn't the fish tank pump water? it was no problem yesterday.

• 4 、Why doesn't the filter in the fish tank spray blisters? How to solve it?

• 5 、Bucket external fish tank filter bucket does not absorb water how to do, forget to pull the power supply when changing water?

• 6 、The reason why there is no water out of the fish tank filter

The filter of the fish tank does not absorb water, it rattles loudly, what is the reason, and the crossbeam is green.

The sound of the filter is caused by the air in the machine, which causes the motor to idle. If you see my answer before the filter burns out, turn off the power quickly, and then make sure that the air in the filter is emptied before running.

The fish tank filter.bucket does not absorb water, which is usually the problem of the pump. It may be that the water level is lower than the pump body or the air leakage at the joint of the suction pipe, or it may be that the rotor of the pump accumulates too much dirt, which affects its operation. Generally, after finding a problem, you need to turn off the filter in time, and then carry out inspection and maintenance.

The water mark is below the water mark and the machine is burnt out. Something in the filter was stirred, so that the filter did not work properly and burnt out. Generally speaking, the water pump can not be repaired when it is broken. Buy a new one. It is recommended to buy a submersible pump. This kind of pump has no sound at all, only the sound of water flow.

The fan blade of the wall-mounted fish tank filter moves normally, but the reason for not absorbing water may be that the suction is not enough: it causes the blade of the wall-mounted fish tank filter to move normally, but the reason for not absorbing water may be insufficient suction. This may be due to the height or shape of the fish tank.

Launching overflow impact. A piece of biochemical cotton can be placed at the impact to make the water "soft landing" sewer resonate. A spiral silencer can be added to the pipe to impact the water surface of the bottom cylinder. It can be extended below the water surface or installed with filter bag to impact the water surface of the main cylinder.

What if the filter in the fish tank can't absorb it?

The water mark is below the water mark.What to do if the fish tank filter doesn't absorb water?The machine is dry and burnt out. There's something stirring in the filter.What to do if the fish tank filter doesn't absorb water?Causing the filter not to work properly and burnt out. Generally speaking, if the water pump is broken, it can't be repaired.What to do if the fish tank filter doesn't absorb water?OfWhat to do if the fish tank filter doesn't absorb water?Oh, buy a new one. It is recommended to buy a submersible pump. This kind of pump has no sound at all, only the sound of water flow.

Generally, after finding a problem, you need to turn off the filter in time, and then carry out inspection and maintenance. If the water level is too low, the bucket needs to be higher, if the rotor has dirt, it needs to be cleaned in time, and the motor problem had better be replaced.

The first is to lower the suction port of the fish tank and shorten the distance between it and the bottom of the tank, so as to increase the suction. The second method is to change to a more powerful filter pump, but it should be noted that the power of the filter pump is generally related to the size of the fish tank, if it does not match, there will be some problems.

If it is not enough, it needs to be replaced. To eliminate the problem of power, that is, the water permeability of the filter layer is not enough, the first need to check whether the filter layer is too dirty, too dirty will increase resistance, resulting in weak suction, cleaning can be solved, in addition, the filter layer is too thick or the medium is too dense will also make the suction small, the medium needs to be reduced or replaced.

At the valve, the water level in the cylinder rises without passing through the air outlet, while the overflow starts to work and forms overflow after the air inside is discharged. After the water level drops, the air inlet is fed and siphon is converted into overflow. This cycle is generally used for out-of-cylinder filters.What to do if the fish tank filter doesn't absorb water?The building is mainly used as drainage to seal up the vent of the valve.

Waterfall filter why didn't the fish tank pump water? it was no problem yesterday.

The main contents are as follows: 1. The pump for filtration is still used to pump water out when changing water. Can plug the pump out for trial, if it can not turn, it is recommended to disassemble the pump, clean the rotor and plug in again, if there is no response, then it is broken, according to the information of the pump nameplate can be re-purchased and replaced.

2, it is likely to be blocked, or something is stuck in the water pump, the light does not turn, or it is broken, to see if it can be sent for repair.

3. The water level is below the water level and the machine is burnt out. Something in the filter was stirred, so that the filter did not work properly and burnt out. Generally speaking, the water pump can not be repaired when it is broken. Buy a new one. It is recommended to buy a submersible pump. This kind of pump has no sound at all, only the sound of water flow.

Why doesn't the filter in the fish tank spray blisters? How to solve it?

The end of the transparent pipe must be exposed to the air before bubbles appear. And the end can adjust the amount of air intake. And your water level is a little low, it is recommended to raise the water level, as far as possible to fill up, the filter should be completely immersed in water.

The water mark is below the water mark and the machine is burnt out. Something in the filter was stirred, so that the filter did not work properly and burnt out. Generally speaking, the water pump can not be repaired when it is broken. Buy a new one. It is recommended to buy a submersible pump. This kind of pump has no sound at all, only the sound of water flow.

The water level may be too low, causing air to enter. It could also be that the pump is damaged or there is no electricity.

Bucket external fish tank filter bucket does not absorb water how to do, forget to pull the power supply when changing water?

1. You said you forgot to pull the plug the last time you changed the water plug, it should be 1. Generally speaking, the water pump can not be repaired when it is broken. Buy a new one. It is recommended to buy a submersible pump. This kind of pump has no sound at all, only the sound of water flow.

2. From the limited situation introduced by myself, one is to inhale air in the barrel and the pump, and the other is to cause overheating and burning damage due to lack of water cooling. If there is still rotating movement after power transmission, the possibility of entering the air is very high, so it needs to be emptied.

3. Generally, after finding a problem, you need to turn off the filter in time, then carry out inspection and maintenance. If the water level is too low, the bucket needs to be higher, if the rotor has dirt, it needs to be cleaned in time, and the motor problem had better be replaced.

The reason why there is no water out of the fish tank filter

1. The water level is below the water level and the machine is dry and burnt out. Something in the filter was stirred, so that the filter did not work properly and burnt out. Generally speaking, the water pump can not be repaired when it is broken. Buy a new one. It is recommended to buy a submersible pump. This kind of pump has no sound at all, only the sound of water flow.

2. The fish tank filter bucket does not absorb water, which is usually the problem of the pump. It may be that the water level is lower than the pump body or the air leakage at the connection of the suction pipe, or it may be that the rotor of the pump accumulates too much dirt, which affects its operation. Generally, after finding a problem, you need to turn off the filter in time, and then carry out inspection and maintenance.

3. The reasons why the filter does not filter may be as follows: the concentration of pollutants in the influent is too high, resulting in excessive filter load, and impurities quickly penetrate the filter bag. It leads to the deterioration of the effluent quality.

ASIAN AROWANA：

Great Baca to a few days and so on albino black emperor

24k Golden Arowana Twelve years of red dragon

What to do if Basia doesnt eat dead

Is it snowing over you

Hellow guys new here...