Illustration of Minjiang dragon fish tank (where is Minjiang fish tank made)

×

Illustration of making dragon fish tank in Minjiang River

This article tells you about the illustration of the Minjiang dragon fish tank and the relevant information about where the Minjiang Fish tank is produced. I hope it will be helpful to you and don't forget to pay attention to our Xianglong fish Farm.

The contents of this article:

• 1 、Make a fish tank tutorial

• 2 、How to make your own fish tank?

• 3 、Steps of filter installation structure at the bottom of Minjiang brand one meter two fish tank

• 4 、The making skills of arowana tank

• 5 、How to make a simple fish tank

Make a Fish tank tutorial

First: choose and buyIllustration of making dragon fish tank in Minjiang RiverThe variety and thickness of glass

To make an ordinary fish tank, choose car-grade white float glass, if you want to make the fish tank more transparent.Illustration of making dragon fish tank in Minjiang RiverThen choose ultra-white glass grass tank dragon fish tank sea water tank generally choose ultra-white to do more than how big the tank needs to choose how the glass, white flotation and ultra-white basically divided into 5mm 6mm 8mm 10mm 12mm 15mm 19mm and so on.

Second: the tools needed to stick the cylinder:

(1) glass glue gun, glass glue, right angle clip, tape measure, triangle board, art pattern paper, glass knife, bracket, folder, etc. The thickness of the glass.

Cymbal

Cymbal

Cymbal

Second: the step of touching the fish tank is to cut the edge of the glass and then measure the size of each piece of glass with a tape measure to see how much the size error of the glass is, and then each piece of glass is stained with masking paper. Glue the jar together and save a lot of words. Everyone's adhesive method is different. I won't say much. Anyway, if the jar is not leaking, it will be OK.

Third, adopt the method of reinforcement:

(1) for the 1.5-0.6-0.75 cylinder, a double 12mm bottom is used to replace the bottom reinforcement, which is both firm and beautiful, and can prevent fish from scratching or scaling at the bottom.

(2) the upper cylinder can be reinforced with eyelet or opening reinforcement along the downward direction of 10 cm, and the edge can be ground with the lower corner of 12mm glass. Long tendons at the bottom, horizontal tendons at the top.

(3) the four corners of the outside of the fish tank should be glued with black right-angle wrapping material.

(4) I usually use black lacquered glass for the upper and lower edge of the fish tank. Fish friends are free to choose edge materials such as wood, marble, various colors of painted glass, which is both beautiful and not easy to hurt adults and children.

Fourth, the filtering methods of all kinds of fish tanks:

(1) bottom filtration: bottom filter tank + triangular overflow side filter.

The bottom filter tank is made according to the above picture mode, and the actual size is: long 1500mm, wide 500mm, high 400mm. Ordinary glass with a thickness of 8mm. It is divided into three or four compartments, the first is to put filter cotton to play the role of physical filtration, the second is to put bacteria houses and glass rings to play the role of biochemical filtration, and the third is a water purification tank with a built-in large flow submersible pump (3000 to 8000L/H / h) to pump the filtered water back to the fish tank. The power supply of the submersible pump is connected to the bottom cabinet, and the outlet pipe of the pump is connected with the upper pipe with a hose to facilitate the replacement of the pump when the pump is broken. The first frame can be slightly narrower, and the third frame can be slightly wider. The cotton filter in the first grid can be placed in multiple layers, and each layer of cotton filter is separated by biochemical rings or biochemical balls to facilitate underwater infiltration. Filter cotton is stuffed into the gap between the upper spacer glass and the bottom. The height of the spacer glass on each grid is the same, the size of the lower spacer glass should be decreased in turn, and the height difference is 3 cm. The upper spacer glass is 1.5 cm away from the bottom of the filter, and the distance between the upper and lower spacer glass is 2 cm. The triangular overflow area is separated by ordinary 0.8 cm glass at the back of the right side of the fish tank. The upper spacer glass in the overflow area uses double glazing, a total of three outermost layers are opened with an acrylic fish comb upper opening and lower opening, the upper opening of the fish comb flavor oil film and floating objects on the water surface, and a 1.5 cm piece of glass is padded at the lower end to leave a gap in the lower water intake.

Two holes are drilled on the bottom of the cylinder in the overflow area, namely the lower water hole and the upper water hole. The diameter of the water hole is 50 holes, and the water pipe is sealed with glass glue after the water pipe is added with a sealing gasket. the sewer pipe passes directly through the bottom of the cylinder and the cabinet surface of the bottom, connects it to the top of the first tank of the lower filter, and drains the water into the lower filter. After the sewer pipe extends vertically under the bottom cabinet surface, the PVC pipe of appropriate length is bonded according to the height of the bottom cabinet surface and the lower filter tank, then the diameter is changed, and finally the appropriate PVC pipe is connected to the top of the first filter of the lower filter tank.

The upper water hole is 25 pipes in diameter, which is filled with 25PVC upper water pipe, and the seal is strengthened by means of casing bonding, sealing gasket and glass glue inside and outside the cylinder bottom. The upper water pipe is directly connected to the upper filter tank, and then the water is filtered and discharged into the triangular overflow area at the back of the left side of the fish tank.

A biochemical ring is filled in the triangular overflow backgas lift area, and an oxygen pump is installed to provide a large amount of oxygen for nitrifying bacteria.

(2) Upper filtration: the filter box is stained on the rear cylinder wall of the main cylinder.

The upper filter tank is made of ordinary glass with a thickness of 0.5cm. The size is as follows: the length is the length of the inner diameter of the fish tank, and the width is the appropriate width to see how you do it. It is convenient to add a lid along the upper edge of the tank. The horizontal sides of the filter tank are directly glued to the glass on both sides of the fish tank, and the rear glass of the fish tank is behind, and the bottom is the rear of the fish tank. It is divided into four grids, from right to left: the first is the upper water pipe hole, the second is the filter cotton, the third is the biochemical ring or biochemical ball, and the fourth is the sewer. The first and last grids can be slightly narrow, and the middle three squares should be wide to place more biochemical filter materials. The second filter cotton is divided into multiple layers, and the top layer is coarse filter cotton, and several layers of fine filter cotton are placed downwards according to the depth of the filter. Each layer of filter cotton can be separated by biochemical rings to facilitate underwater infiltration. The height of the spacer glass on each grid is the same, the size of the lower spacer glass should be reduced in turn, the height difference is 2 cm, and the bottom corners of the lower spacer glass are ground into triangles to avoid the glass glue at the bottom of the fish tank and facilitate bonding and sealing. The upper spacer glass is 1 cm away from the bottom of the filter, and the distance between the upper and lower spacer glass is 2 cm. The upper end of the first spacer glass is pierced with a semicircular hole of 3cm in diameter to place the upper water pipe; the bottom of the first glass is punched into a 3cm diameter upper water pipe hole with a 2cm PVC upper water pipe, which does not need to be bonded and sealed. The launching bottom hole is located on the left side of the filter tank, and the width of the upper side reinforcement should be left. The diameter of the bottom hole is 2.1cm, and the PVC launching short pipe is worn inside, and the bottom of the pipe should be higher than the water surface. (3) back filtering: the filter trough is pasted on the back of the main cylinder to achieve the filtering effect.

Cymbal

(4) side filtration: the filter tank is pasted at one end of the main cylinder to achieve the filtering effect.

Cymbal

Fifth: making fish tank head:

The fish tanks I make generally use glass with black mirror glass or transparent glass. I generally choose to use 5mm as the glass lid. I can also use aluminum plastic plate PVC board and so on to prevent moisture and deformation. The cylinder head is divided into three or two separate pieces, which can also be flipped back and forth or push and pull left and right. I do more push and pull covers, the back piece of which is slightly wider than the upper filter slot, and it is convenient to open and clean the filter trough; the middle piece is a lamp trough, basically motionless, and two lamps are fixed parallel to the left and right. The front piece is often lifted to facilitate feeding, adding water and other daily management. Sixth: fish tank beautification:

Before beautifying the fish tank, see what kind of fish you raise if you raise a red dragon on a black or blue background and tank bottom to highlight the red color of the red dragon. The glass glue is made of black glue, the back, sides and bottom of the fish tank are all black with black post-it stickers, and the black post-it stickers on the bottom can be stuck between the two glass bottoms. The two triangular overflow outer baffles in the fish tank are made of double-layer adhesive glass and acrylic plate fish comb. Cymbal

Seventh: the production of fish tank bottom cabinet:

It can be processed with three kinds of raw materials: one is to use galvanized square tube to make keel frame, wrap aluminum-plastic plate or density board or directly paste decorative glass; the other is to use hardwood as frame, outer aluminum-plastic board or paint-free board. The top of the cupboard is made of a density plate, and on the bottom of the fish tank, stainless steel is used as the skeleton. A round hole of the corresponding diameter is left at the sewer. There are two round holes on the left side of the back of the bottom cabinet to facilitate the penetration of the power cord and the oxygen-filled head. First place the bottom filter and then put the bottom cupboard, and finally put the fish tank. The four doors of the bottom cabinet are opposite to each other, and the bottom filter is placed on the right side of the bottom cabinet, leaving space on the left to install the power supply, etc. Cymbals

How to make your own fish tank?

1. Tools / raw materials: American pattern tape, knife, filter box. First of all, to cut the glass, to use the best knife, the scale measured before the knife should be accurate, before the knife, you can use a brush dipped in a little fire oil, coated in the glass under the knife, and then under the knife.

2. Then use a grindstone to grind the edge into a rough surface, which is called "grinding mouth" in the production of the aquarium.

3, followed by sticking Meiwen tape, in order to strengthen the glue, it is best to paste Meiwen tape twice, look at the seams, very neat!

4. Then there is the water baffle of the corner filter, which is glued to the corner filter. You can take a look at the seams of the corner filter.

5. Look at the effect, as shown in the following figure.

Extended data

Use common sense

1. If you want to make the fish tank look good, you must put aquatic plants in the water. There are many kinds of aquatic plants in the aquarium shop. You can choose the ones you like. Water plants need to be fixed, inevitably need stones, small stones are not easy to clean, you use the big Yuhua stone to press the water grass roots, when cleaning, just take the Yuhua stone out and wash it.

2. You can put some rockery, real rocks and corals in the fish tank, so that you can create a very lifelike undersea world. You can put wallpaper on the back of the fish tank, which can be found in aquarium shops. In the process of raising fish, the residue after feeding and the decomposition of fish can produce a large number of harmful substances.

3. So with appropriate filtration equipment, the beneficial fungi cultivated in the filtration equipment can decompose a large number of harmful substances, make the fish grow healthily, and keep the water clean. The commonly used materials in the filtration equipment are filter cotton, biochemical cotton, ceramic ring, etc., the filter materials are cleaned once a month, do not use detergents and other things when cleaning, and do not need to wash particularly clean, so as not to re-cultivate beneficial bacteria.

4. If there is no filtration equipment, water can be changed frequently to meet the growth requirements of fish, and the standard of water change should be changed frequently and less. Every time water is changed, the water should be changed every 3 days, according to the turbidity and temperature of the water body, once a day in summer and once every 3 days in winter.

5. At present, goldfish tanks have many shapes and materials. Consumers can choose different types of goldfish tanks according to fish habits, environmental requirements. and personal preferences.

6. This kind of fish tank usually needs to be thoroughly cleaned only once every six months. Wash the filtered cotton every 15 days and add a little water a week to make up the evaporated water. What's more, just wash the stones.

7. There are various forms of goldfish tank, it is best not to choose a round goldfish tank, because in this way, the shape seen by the fish is distorted, which will make it feel very uneasy.

Reference: Baidu encyclopedia-goldfish bowl

Steps of filter installation structure at the bottom of Minjiang brand one meter two fish tank

Is the landlord a woman?

The bottom filter only needs to lay out the bottom filter plate, and then connect the pipe to the pump, the pump to buy a three-in-one pump, and finally spread sand on the bottom filter plate. It can also be extended to bottom filtration + upper filtration on the basis of bottom filtration, only need to add an upper filter box and an upper water pipe. TB is on sale.

Additional follow-up questions are welcome

The making skills of arowana tank

1. The length of the master cylinder is 150cmIllustration of making dragon fish tank in Minjiang RiverWide 65cm, high 50cm, black film pasted on three sides of fish tank, specially designed for arowana culture. Generally, when cultivating arowana, the body length within 22cm is suitable for black background color, while the above is suitable for blue background color, which is mainly to match the hair color of arowana. Different environmental colors have different effects on the hair color of arowana.

2. Ordinary float glass is used to select the main material of the fish tank, and the upper filtration method is used for filtering. About heating rodsIllustration of making dragon fish tank in Minjiang RiverI generally recommend it to be used in the lower part of the fish tank, or on the upper and lower side. Affected by the rise of warm water and the decrease of cold water, this will help to speed up the balance of temperature in the water body.

3. The filtering part of the fish tank, because the master uses the upper filter and is divided into two main cylinders, so two upper filter tanks are made, which are used independently and do not interfere with each other, all made of ordinary glass. Filter material selected filter cotton, biochemical cotton, ceramic ring, biochemical ball, etc., do not care about the simplicity of this filter material, often the simpler the filter material effect is the best. The filter material focuses on practicality, not on the cost of the material.

4, fish tank is divided into upper and lower two-layer structure, the design is the same, all filters, cylinders, configuration are also the same. The fly in the ointment is that if this design, filtration should be used drip filtration may be better. If you don't need to consider aesthetics, it's better to choose a more obvious filtering method.

How to make a simple fish tank

Eleven steps to teach you how to make your own fish tank:

First: the choice of glass varieties and thickness

Tank bottom with 1.5 cm tempered glass, surrounded by 1.2 cm tempered glass.

Second: Reinforcement measures taken:

(1)The bottom of the cylinder adopts double bottom instead of bottom lacing, which is firm and beautiful, and can prevent arowana from scratching on bottom lacing. 1.5cm outsole

The inner bottom is 1 cm of ordinary glass. The inner bottom is 1.2 cm shorter than the outer bottom in length and width, so as to leave the thickness of four facade glass.

。

(2)The upper cylinder is reinforced with double-layer lacing along the downward 15 cm, and the lower corner material of thick glass can be used. Vertical lacing is at the bottom and horizontal lacing is at the top.

The rear lacing of the fish tank can be combined with the bottom of the upper filtering groove, and a single-layer lacing can be adopted.

(3)The four strong ribs on the outside of the fish tank are bonded and reinforced with dark aluminum alloy right-angle materials, which can also beautify the effect.

(4)The four upper corners of the fish tank are bonded and reinforced after being fixed with a triangle modified by a dark aluminum alloy groove. At the same time, it also plays a role in beautifying and preventing glass.

Sharp point pricks the hand.

Third: fish tank size:

Length: 1800-2000mm, depending on the size of the space; width: 70mm; height: 70 mm. After adding water, the water surface is 50mm high, leaving a space of 20 mm.

Fourth: layout of facilities in the cylinder:

(1)Filter mode: bottom filter + double triangle overflow side filter + upper filter.

(2)Oxygen charging mode: the filter outlet is designed as triangle area reverse gas lift, and a submerged motor for upper filtration is added (with oxygen charging and no filtration).

。

(3)Heating method: double 300W electronic temperature control heating rod heating, inclined 45 degrees angle placed under the filter outlet and near the sinking motor.

(4)Increase water flow mode: In addition to flushing at the outlet of the filter, install a submerged motor (with oxygenation, without filtration).

(5)Lighting: top double plant lights (red)+ tank bottom double water lights, power is 30W.

(6)Anti-jump: stick upper filter on top of upper lacing near the rear of cylinder, with length equal to cylinder length, width of 30cm, height no more than cylinder upper edge, square

Then cover the cylinder cover, the bottom can directly borrow the lacing plate, that is, the width of the transverse lacing at the rear of the fish tank is 30 cm. Front part of upper filter, flat above lacing

Two thick glass plates with cover, one of which should be fastened tightly to half of the tank, and a slight gap can also be used. One is to prevent jumping, and the other is to prevent moisture evaporation.

Hair; another piece can leave a gap of 10 cm to facilitate feeding and fishing up the remaining bait.

Fifth: fish tank cover:

With woodworking board processing, with dark aluminum-plastic plate package decoration, preferably with the bottom cabinet with color, to prevent moisture deformation. The cylinder head is divided into three separate pieces, and finally

The width of the surface is the same as that of the upper filter groove, which is 30 cm, which is convenient to open and clean the filter groove; the width of the middle one is 25 cm, which is basically fixed, and the bottom side is fixed in parallel.

Two upper lights. The outermost piece is 15 cm wide and is often lifted for feeding, watering and other daily administration.

Sixth: fish tank beautification:

Because it is used to raise red dragons, the fish tank should be black as a whole to highlight the red color of red dragons. The glass glue is made of vinyl, and the back and both sides of the fish tank are selected.

Black instant stickers are used on both sides and bottom to make them black. The black instant stickers on the bottom can be stuck between two layers of glass. Two triangular overflow stops inside the fish tank

The board adopts double-layer adhesive glass, and black instant stickers are also stuck between the two layers of glass to block the filter material. 15 cm down the top edge of the fish tank with a black decorative plate

Adhesive trim.

Seventh: fish tank placement:

(1)Fish tank placed in the customized bottom cabinet, under the cushion foam board anti-crash, bottom cabinet length: 1800-2000mm, depending on the size of the space; width: 70mm;

Height: 60 mm.

(2)The bottom cabinet should be placed on a whole board and leveled with a level ruler. It should be placed perpendicular to the floor to distribute the weight of the fish tank.

Light floor pressure.

(3)Fish tanks should be kept where few people move and arowana is not easily frightened. The best position is against the east or west wall, and there is no direct sunlight.

Prevent green algae from growing in the tank due to sunlight and be close to the power supply.

Eighth: fish tank bottom cabinet production:

Available in two raw materials processing: one is to use round steel pipe for six legs support, thick angle iron for beams, wrapped aluminum plastic plate or density plate; the other is to use hard

Wooden frame, six legs support, wrapped aluminum plastic plate or density plate. Density board is used on the top surface of the cabinet, and corresponding holes are reserved at the upper and lower water outlets aligned with the bottom of the fish tank.

The diameter of the hole. If using aluminum-plastic plate outsourcing, choose dark color; if using density plate outsourcing, paint dark color. Leave two diameters on the left side of the back of the cabinet

5 cm round hole for easy insertion of power cord and oxygen charging head. To facilitate the placement of the bottom filter tank, the bottom cabinet does not need to be added to the bottom, but it needs to be reinforced with a lower beam.

Put the bottom filter tank first, then put the bottom cabinet, and finally put the fish tank. The bottom cabinet has four open doors, the bottom filter tank is placed on the right side of the bottom cabinet, and the left side is left empty.

to install power, etc.

Ninth: fish tank filter production:

The upper filter tank is made according to the model shown in the above picture. It is made of ordinary glass with a thickness of 0.5 cm and a size of 30 cm and a length corresponding to the inner diameter of the fish tank

The height of the filter tank is not higher than that of the upper edge of the fish tank. The two lateral sides of the filter tank are directly adhered to the glass on both sides of the fish tank. The rear is the rear glass of the fish tank. The bottom is fish.

Rear bracing of cylinder. Divided into six cells, from right to left in order: the first cell for the water pipe hole cell, the second cell put filter cotton, physical filtration,

The third to fifth cells put biochemical ring or biochemical ball, biochemical filtration, the sixth cell for the sewer. The first, second and sixth compartments may be slightly narrower,

The middle three cells should be wide to accommodate more biochemical filters. the second grid of filt cotton is arranged in multiple layer, and that top layer is coarse filter cotton, and the filter cotton is arranged downwards according to the depth of the filter groove

Put several layers of fine filter cotton in turn, and the layers of filter cotton can be separated by biochemical rings to facilitate underwater infiltration. The glass height of each cell is the same, and the lower space is the same.

Glass should be reduced in size in turn, height difference of 2 cm, the bottom two corners of the lower interval glass are ground into triangles to avoid the glass glue at the bottom of the fish tank, square

Then glue the seal. The distance between the upper spacer glass and the bottom of the filter tank is 1 cm, and the distance between the upper and lower spacer glasses is 2 cm. The top of the first compartment glass is straight

A semicircular hole of 3 cm in diameter is drilled in the bottom glass of the first compartment to accommodate a water supply pipe; a water supply pipe hole of 3 cm in diameter is drilled in the bottom glass of the first compartment, and a PVC water supply pipe of 2 cm is penetrated inside.

No adhesive seals required. The bottom hole is set on the left side of the filter tank, and the width of the upper side lacing bar shall be reserved. The diameter of the bottom hole is 2.1 cm, and the PVC is 2 cm inside.

The bottom of launching short pipe shall be higher than water surface, and launching shall fall into triangle overflow anti-gas lift area.

Tenth: bottom filter and supporting facilities production:

The bottom filter tank is made according to the above picture mode, the actual size is: long 1500mm, wide 500mm, high 400mm. Glass with a thickness of 1 cm

Through the glass. It is divided into five grids, the first grid put filter cotton, play the role of physical filtration; the second to the fourth grid put biochemical rings and biochemical balls, biochemical filtration

Use; the fifth frame is a storage tank with a built-in large flow pumping motor (3000 to 4000L/H (liter / hour), using submerged type. If it is not submerged

In addition, it is inconvenient to punch holes in the bottom filter wall.) In order to pump the filtered water back to the fish tank The power supply of the pumping motor is connected to the bottom.

The outlet pipe is connected with the upper pipe with a hose to facilitate the replacement of the motor when the motor is broken. The first frame can be a little narrower and the fifth can be a little wider.

The cotton filter in the first grid can be placed in multiple layers, and each layer of cotton filter is separated by biochemical rings or biochemical balls to facilitate underwater infiltration. Put nylon socks on the outlet of the sewer pipe

Used to filter large stolen goods, convenient cleaning, in order to reduce the number of cotton filter cleaning. Filter cotton is stuffed into the gap between the upper spacer glass and the bottom. Each grid

The height of the upper spacer glass is the same, the lower spacer glass should be reduced in turn, and the height difference is 2 cm. The upper spacer glass is 1 cm away from the bottom of the filter, upper and lower

The distance between the two spacers is 2 cm. The specific glass dimensions are as follows: ordinary glass with a thickness of 0.5 cm; the upper spacer glass is uniformly high.

There are four pieces of 46mmX, 38mm wide, and the height of the lower septal glass is reduced by 1 cm from the first to the fourth, that is, 45mm, 43mm, 43mm, 41mm, 39mm. Lower spacer glass

The bottom corners of the glass are ground into a triangle.

The triangular overflow area is separated by ordinary 0.5 cm glass at the back of the right side of the fish tank. The spacer glass on the overflow area uses double-layer glass, which is black inside.

Post-it stickers, punch two semicircular holes (also known as overflow holes) along the glass with a diameter of 5.5 cm to overflow the oil film and floating objects on the water surface.

The glass height is 52 cm (70-1.5-1-1-15-65). 5), with a width of 40 cm and a glass block of 1 cm at the lower end to leave a gap in the lower water intake; lower septum

The glass is 48 cm high and 35 cm wide, and the bottom corners are ground into a triangle.

Two holes are drilled on the bottom of the cylinder in the overflow area, namely the lower water hole and the upper water hole. The diameter of the sewer hole is 5.5 cm, and the sealing pad of the sewer pipe is inside.

After the glass glue is sealed, the sewer pipe goes directly through the bottom of the cylinder and the bottom of the cabinet, and is connected to the top of the first grid of the lower filter tank, and the water is discharged into the lower filter tank. Get into the water

After the tube is vertically stretched down the bottom cabinet surface, the appropriate length of 3 cm diameter PVC tube is bonded according to the height of the bottom cabinet surface and the bottom filter, and then transferred to 2%.

Change the diameter of the meter, then transfer to a 45-degree elbow of 2cm, and finally connect the 2cm PVC pipe to the top of the first filter of the lower filter tank, and cover the pipe end with a nylon sock.

.

The diameter of the hole in Sheung Shui is 2.1cm, and it is equipped with a 2cm PVC water pipe. The inner and outer casing of the cylinder bottom is glued, sealed and glassed.

The upper water pipe is directly connected to the upper filter tank, and then the water is discharged into the triangular overflow backgas lift area at the left rear of the fish tank (as shown in the following figure).

. The spacer glass of the overflow area is also double-layer, which is sandwiched with black post-it notes, and the bottom corners are also ground into a triangle.

The glass interlayer around the two holes in the upper and lower water is sealed with glass glue to prevent water from seeping into the glass interlayer. To facilitate the change of water

The same pipe is used for water supply and discharge, a valve is added in the horizontal position of the upper pipe, and a valve is added in the vertical position, with an external PVC short pipe and hose.

For changing water. When changing water, close the valve on the horizontal pipe and open the valve on the vertical pipe.

Fill the biochemical ring in the triangular overflow backgas lift area and install a submerged motor (with oxygen, without filtration) to increase the water flow. Charge

The oxygen hole is opened on the spacer glass, and the diameter of the hole can be slightly larger than the diameter of the oxygen port, so as to facilitate the adjustment of the installation position of the submerged motor. Oxygen hole height apparent sink

The height of the oxygen filling port after the installation of the water motor is determined. The outer end of the oxygen port is aligned with the spacer glass, so that the submerged motor can be hidden to prevent arowana.

Bruising.

The reverse air-lift oxygen pump is high-power, with two air heads, one is in the triangular overflow area, and one is used to increase the dissolved oxygen of the water in the cylinder.

In the water storage cell of the bottom filter, it is used to supplement sufficient oxygen for nitrifying bacteria and speed up their growth and reproduction. The oxygenation pump should be placed higher than the fish tank.

To prevent the backflow of water into the oxygen pump and burn out the motor.

Eleventh: electricity safety of domestic fish tanks:

For the sake of beauty, the total power plug of the fish tank is located in the bottom cabinet. For safety, a leakage protector is installed before the power supply is plugged in, and it is equipped with delayed electricity.

Source and battery for heating, oxygenation, lighting and filtration in case of power outage. All electrical switches are set to press switch type to avoid frequent

Unplugging the power plug causes electrical leakage, electrical damage and other accidents.

So much for the introduction of Minjiang dragon fish tank illustration. Thank you for taking the time to read the contents of this site. Don't forget to look for more information about where Minjiang fish tank is made and Minjiang dragon fish tank making illustration.

ASIAN AROWANA：

Is the color of the tiger fish a little blue？ Take a big breath and hang a strip of Taibei yesterday

Having Rieter Arowana is no longer a dream

Siam giant carp (national treasure) Daily snacks

Really rejected I bought it I cant let the opening

Ammonia super high